mlkem-sync/sync_rtl/sha3/sha3_top.v

// sha3_top.v - SHA3/SHAKE top wrapper with valid/ready interface
//
// Implements SHA3-512 (G), SHA3-256 (H), SHAKE-256 (J) over a single
// Keccak-f[1600] core. Supports single-block absorption (Phase 1.1).
//
// Modes:
//   00 = G  (SHA3-512):   rate=576,  suffix=01, msg_len=264, out=512
//   01 = H  (SHA3-256):   rate=1088, suffix=01, msg_len=256, out=256
//   10 = J  (SHAKE-256):  rate=1088, suffix=1111,msg_len=512,out=256
//
// Interface:
//   clk, rst_n  - clock, active-low reset
//   mode[1:0]   - 00=G, 01=H, 10=J
//   data_i      - 512-bit message input
//   valid_i     - input valid
//   ready_o     - can accept new input
//   hash_o      - 512-bit hash output (lower 256 for H/J)
//   valid_o     - output valid
//   ready_i     - consumer accepts output

module sha3_top (
    input              clk,
    input              rst_n,
    input  [1:0]       mode,
    input  [511:0]     data_i,
    input              valid_i,
    output             ready_o,
    output [511:0]     hash_o,
    output             valid_o,
    input              ready_i
);

    // ================================================================
    // FSM state encoding
    // ================================================================
    localparam ST_IDLE    = 2'd0;
    localparam ST_PERMUTE = 2'd1;
    localparam ST_SQUEEZE = 2'd2;

    reg [1:0]  state_r, state_next;

    // ================================================================
    // Absorb state: message || suffix || pad10*1 into rate bits
    // Built combinationally from data_i and mode.
    //
    // G: padded_block = {1, 308'b0, 1, 2'b01, data_i[263:0]}
    //    absorb_state = {1024'b0, padded_block_576}
    //
    // H: padded_block = {1, 828'b0, 1, 2'b01, data_i[255:0]}
    //    absorb_state = {512'b0, padded_block_1088}
    //
    // J: padded_block = {1, 570'b0, 1, 4'b1111, data_i[511:0]}
    //    absorb_state = {512'b0, padded_block_1088}
    // ================================================================
    wire [575:0]  g_pad;
    wire [1087:0] h_pad;
    wire [1087:0] j_pad;

    assign g_pad = {1'b1, {308{1'b0}}, 1'b1, 2'b10, data_i[263:0]};
    assign h_pad = {1'b1, {828{1'b0}}, 1'b1, 2'b10, data_i[255:0]};
    // J: SHAKE suffix is "1111" — all ones, order irrelevant
    assign j_pad = {1'b1, {570{1'b0}}, 1'b1, 4'b1111, data_i[511:0]};

    wire [1599:0] absorb_state;
    assign absorb_state = (mode == 2'b00) ? {{(1600-576){1'b0}}, g_pad} :
                          (mode == 2'b01) ? {{(1600-1088){1'b0}}, h_pad} :
                          (mode == 2'b10) ? {{(1600-1088){1'b0}}, j_pad} :
                          1600'd0;

    // ================================================================
    // Keccak core
    // ================================================================
    wire              kc_valid_i;
    /* verilator lint_off UNUSEDSIGNAL */
    wire [1599:0]     kc_state_o;
    wire              kc_ready_o;
    /* verilator lint_on UNUSEDSIGNAL */
    wire              kc_valid_o;

    keccak_core #(.ROUNDS(24)) u_keccak (
        .clk      (clk),
        .rst_n    (rst_n),
        .state_i  (absorb_state),
        .valid_i  (kc_valid_i),
        .ready_o  (kc_ready_o),      // unused but must connect
        .state_o  (kc_state_o),
        .valid_o  (kc_valid_o),
        .ready_i  (1'b1)   // always accept output
    );

    // ================================================================
    // FSM combinational logic
    // ================================================================
    assign ready_o = (state_r == ST_IDLE);

    // kc_valid_i: start keccak_core during IDLE when input accepted.
    // Driven from state_next to avoid NBA latency: when state_r==IDLE
    // and valid_i→1, state_next=PERMUTE immediately (combinational).
    // keccak_core sees valid_i=1 on the stable cycle before the posedge.
    // On subsequent PERMUTE cycles, busy_r blocks re-start.
    assign kc_valid_i = (state_next == ST_PERMUTE);

    always @(*) begin
        state_next = state_r;
        case (state_r)
            ST_IDLE:    if (valid_i && ready_o)  state_next = ST_PERMUTE;
            ST_PERMUTE: if (kc_valid_o)           state_next = ST_SQUEEZE;
            ST_SQUEEZE: if (valid_o && ready_i)   state_next = ST_IDLE;
            default:    state_next = ST_IDLE;
        endcase
    end

    // ================================================================
    // Output
    // ================================================================
    // Register for squeezed output (only 512 bits needed)
    reg [511:0] squeezed_state_r;

    assign valid_o = (state_r == ST_SQUEEZE);
    assign hash_o  = squeezed_state_r;

    // ================================================================
    // Sequential logic
    // ================================================================

    always @(posedge clk or negedge rst_n) begin
        if (!rst_n) begin
            state_r          <= ST_IDLE;
            squeezed_state_r <= 512'd0;
        end else begin
            state_r <= state_next;

            // Latch squeezed output when keccak_core finishes
            if (state_r == ST_PERMUTE && kc_valid_o) begin
                squeezed_state_r <= kc_state_o[511:0];
            end
        end
    end

endmodule